Sewer Systems

Grinder Pumps

W-Series | WH472 & WR472 Grinder Pump Station

WH472 large

The WH472/WR472 is one of E/One's largest-capacity grinder pump stations. This duplex (2 pumps) station offers a capacity of 476 gallons and can handle flows of up to 3500 GPD.

Drawings & Installation Instructions

WH472/WR472 Drawings (PDF, 1 mb)

WH472/WR472 Drawings (zipped DXF, 12 mb)

Extreme Series Pump Curve (PDF)

WH472/WR472 Installation Instructions (PDF, 2 mb)

Model WH47 Specification — Wired Level Sensor (DOC)

Model WR47 Specification — Wireless Level Sensor (DOC)

Recommended Alarm Panel

E/One Sentry Protect Plus 

Additional alarm panel options are available.

Features

E/One's WH472/WR472 grinder pump station consists of an Extreme series grinder pump inside an open wetwell tank. The grinder pump, motor controls and level-sensing are integrated into a compact unit, easily removable for service.

Solids are ground into fine particles that pass easily through the pump, check valve and small-diameter pipe lines — even objects that are not normally found in sewage, such as plastic, rubber, fiber, wood, etc. The 1-1/4" discharge connection can be adapted to any piping materials that meet local code requirements. The internal check valve assembly, located in the grinder pump, is custom designed for non-clog, trouble-free operation.

  • The WH472 is the “hardwired,” or “wired,” model where a cable connects the motor controls to the level controls through watertight penetrations.
  • The WR472 is the “radio frequency identification” (RFID), or “wireless,” model that uses wireless technology to communicate between the level controls and the motor controls.

The tank is made of tough, corrosion-resistant polyethylene. Designed specifically for low pressure sewer applications, the optimum tank capacity of 476 gallons provides ample storage. A single WH472/WR472 can accommodate flows of up to 3500 gallons per day.

Stations are available in several heights to accommodate various burial depth requirements. See drawings (above) for more information. E/One requires the installation of its stainless steel UNI-LATERAL to prevent backflow from the sewer system from entering the grinder pump station.

About the E/One Grinder Pump

The grinder pump is automatically activated and runs for very short periods. Electrical consumption of the grinder pump is low and will vary with actual water consumption.

E/One grinder pumps do not require preventive maintenance and boast an average of eight to 10 years between service calls. If service is required, the  one-piece core eliminates the need for in-field troubleshooting and servicing — the pump core can be quickly pulled out and replaced, meaning minimal maintenance costs and inconvenience for the property.

Operational Information

Motor: 1 HP, 1725 rpm, high torque, capacitor start, thermally protected, 240 or 120 volt, 60 hertz, 1 phase

Inlet Connections: 4" inlet grommet standard for PVC pipe. Other inlet configurations available from factory.

Discharge Connections: Pump discharge terminates in 1-1/4" NPT female thread. Can easily be adapted to 1-1/4" PVC pipe or any other material required by local codes. E/One requires the installation of its stainless steel UNI-LATERAL to prevent backflow from the sewer system from entering the grinder pump station.

Discharge:
15 gpm at 0 psig
11 gpm at 40 psig
7.8 gpm at 80 psig

US and foreign patents issued and pending.

Electrical Information

A dedicated 30A breaker is required, with #10 wire, for 240V single phase. You need to bring L1, L2, N and Gnd to the E/One panel.

If only 208V power is available, a buck boost transformer is required to boost 208V to 240V. The E/One pump requires a minimum of 216V to start and run reliably.